Daily inspection and repair of machine tools

　　your Welding helmet. Before starting the machine daily, carefully check the working conditions on the laser working gas in addition to cutting gas. If the gas pressure isn't enough, it should be replaced with time.

　　b. Check whether this X-axis zero point, Y-axis zero point, Z-axis zero place, laser preparation status and various buttons are damaged, (check your indicator lamp).

　　c. Check whether the zero point in the X-axis, Y-axis, and Z-axis, that limit switch, and the mounting screws of the impact block are free, and whether the limit switches of each axis are sensitive.

　　d. Check whether the circulating water level in the chiller is sufficient. Or, add it in time frame.

　　e. Check whether there exists any leakage in the particular circulating water circuit from the external light path. Leakage have to be handled in time, otherwise living of the optical lens are going to be affected.

　　f. After reducing is completed daily, examine the focus lens to get damage.

　　g. Check whether the bellows on the external light path is definitely burned or damaged.

　　they would. After the daily function is completed, clean up the cutting waste in time, clean the work web-site, and keep the work site tidy and wash. At the same time, do a good work of cleaning the equipment to ensure all parts of kit are clean and free of dirt.

　　j. After the particular daily work is carried out, open the drain valve to the air reservoir at the end of the air compressor to be able to drain, and close the drain valve following waste water is cleared.

　　k. After the every day work is completed, press the shutdown step to de-activate the machine and turn off the total power towards entire machine.

　　Weekly and also occasional maintenance of equipment tools

　　a. Regularly cleanup the debris passing with the ventilation outlet to assure the ventilation effect.

　　b. Regularly check the filter inside the air circuit to eliminate water and debris in that filter.

　　c. Periodically find out if the trip switch bracket as well as striker bracket screws will be loose.

　　d. It is necessary that will promptly clean the dust within the filter screen of the particular electric control cabinet to be sure good ventilation so as to facilitate the heat dissipation involving internal electrical components.

　　age. The chemical bed well-timed clears the guide rail and protects the debris while in the skin cavity so as to avoid damaging the guideline rail, thereby prolonging the service life in the guide rail.

　　f. Following machine tool is established, use it for time to readjust the machine tool's level to confirm the cutting accuracy of the machine tool.

　　g. Some other week must check the particular X-axis guide rail in addition to screw, Y-axis guide railroad and screw, Z-axis manual rail and screw lubricant responding to their, keep the lubrication of every Welding helmet moving part, extend TIMES, Y, Z axis guide and wire The service life of the bar.

　　h. Inspect the surface in the mirror and the concentrating lens for irregular conditions (at least once a month) in the class environment and clean the optical lens in time to ensure its assistance life.

　　Maintenance of Optical The len's Outside Machine Tool

　　your. The surface of that optical lens (mirror, highlighting lens, etc. ) is not to be directly touched personally. This can easily cause scratches within the mirror surface. If there is oil or dust around the mirror, it will seriously affect the usage of the lens and the lens need to be cleaned in time.

　　b. Optical lenses cannot be washed with water or detergent. The surface of the lens is coated with a special film. Cleaning the lens using these will damage the surface on the lens.

　　c. Do not place the lens within a dark, damp place. This can cause the lens surface to age.

　　d. The surface belonging to the lens is covered along with dust, dirt, or drinking water vapor. It is easy to absorb the laser and cause problems for the coating of the actual lens. At light, the grade of the laser beam can be affected, and when it is heavy, no laser smile is generated.

　　e. Should the lens is damaged, contact Han's laser service department to do the repair. Try not to work with damaged lens. Otherwise it is going to damage the repairable zoom lens.

　　f. Do not use an excessive amount of pressure when installing as well as replacing reflectors or concentrating lenses, as this could potentially cause distortion of the contact and affect the hug you quality.